Our strength lies in the quality

Your direct line

+49 8435 150

TIPPER SEMI-TRAILERS SITE LOGISTICS

Our tipper semi-trailers can transport big loads thanks to high axle loading technology. The compact 4-axle semi trailer for example, which is based on the design of the 2-axle semi trailer is especially economical. This tipper semi trailer can be ordered with forced steering as an option, which enables exceptional manoeuvrability. All tipper semi-trailers have modern chassis and the electronic braking system EBS is fitted as standard. Also the highly used vehicle parts are designed to have the least possible wear, which means the trailer operates safely on the building site as well as on the road. The tipper semi-trailers from REISCH are configurable for all areas of operation.

RHKS-2-SR06

Total weight:31.000 kg
Empty weight:ca. 5.210 kg
Base data:
Total weight:31.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:20.000 kg
Empty weight:ca. 5.210 kg
Payload:ca. 26.398 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-06) with standard frame height, wheelbase approx. 4,060 mm, axle distance 1,810 mm suitable for 2-A-tractor unit equipment.


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device



without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor unit equipment must be prepared / unlocked it).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


Tires 425/65 R 22.5 TL 165 K Goodyear KMAX T M + S (regional profile).


Steel-rims 13,00x22,5 10-hole ET 0 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Additional flaps mounted on the mudguard of the first axle.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Bracket on the chassis longitudinal beam on LEFT in driving directional.


HYVA-high / low pressure front lift cylinder, about 5,030 mm stroke (about 75 liters of oil demand), operating pressure 170 to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round dump 6,200 / 1,450 mm (with internal tailgate with chute)


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Internal steel pendulum tailgate (with chute).


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


REISCH- driving jacket


RHKS chassis (2-06) with standard frame height, wheelbase approx. 4,060 mm, axle distance 1,810 mm suitable for 2-A-tractor unit equipment.

"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-06) with HIGH frame height for ASH debited from about 1270-1360 mm, wheelbase approx 4,060 mm Axle distance 1,810 mm fits on 2-A-Tractor unit equipment.

- the specified semi-trailer height range applies only to tires 425/65 R 22,5. Depending on the desired axis type and tires, the fifth wheel may change and may make unnecessary a high frame. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-06) with EXTRA HIGH frame height for ASH debited from about 1370-1420 mm, wheelbase approx 4,060 mm Wheelbase 1,810 mm fits on 2-A-Tractor unit equipment

- Required in extem highly constructed fifth wheel or tractor with caddy assembly
- The specified Aufsattelhöhenbereich applies only to tires 425/65 R 22.5. Depending on the desired axis type and tires, the fifth wheel can change and do not necessary possibly an extra high frame. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.


Jost gearbox support winch with T-foot CENTER mounted on the vehicle (only for empty seats).



(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x SAF-10-to-axles (ET120 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm (OFFROAD).


2 x BPW-11-to-axles (ET 0 mm) for 22.5 "-E tires with drum brake 420 x 200 mm and handlebar springs 100/57 mm.


2 x BPW-10-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-adhesive baffles and 100/57 mm handlebars.


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis on LEFT in driving directional.


2-sided axle lift for 10/11-to-axle on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. white (without pushbutton and switch installation in trucks / tractors)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

- Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor unit equipment must be prepared / unlocked it).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

-for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation axle lift / Anfarhilfe on the trailer; Adjusting the brake pressure at finisher brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

-for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation axle lift / Anfarhilfe on the trailer; Adjusting the brake pressure at finisher brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor unit equipment).
- In addition we recommend KNORR-TIM (s.Art number BR02100.) Or WABCO SMARTBOARD (s.Art number BR02120.) For setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation axle lift / Anfarhilfe on the trailer; Adjusting the brake pressure at finisher brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Loadingmanometer (0-10 bar)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.


Tires 385/65 R 22,5 TL 160 K Aeolus AGC28 M + S (coarse construction site profile).


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (s.Art no. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (s.Art no. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting Kippzylinderlagerung below (2 SMST.)
- Front lifting Kippzylinderlagerung above (2 SMST.)
- Tilting shaft rear (4 SMST.)
- 2-hook linkage lock (6 SmSt.)



PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Mounting on the axle assembly in FR RIGHT.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please Specify exactly!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on right in driving directional


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on Right in driving directional


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 6,200 / 1,550 mm (with internal tailgate with chute)

-Volume then approx. 20,2 m?


Steel round trough 6,200 / 1,650 mm (with internal tailgate with chute)

-Volume then approx. 21,6 m?


Steel round trough 6,500 / 1,450 mm (with internal tailgate without chute)

-Volume then approx. 19,7 m?


Steel round trough 6,500 / 1,550 mm (with internal tailgate without chute)

-Volume then approx 21,2 m?


Steel round trough 6,500 / 1,650 mm (with internal tailgate without chute)

-Volume then approx. 22,7 m?


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT or RIGHT in driving directional.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


Ascent ladder divided at the side wall on LEFT in driving directional. Upper half firmly screwed to dump side wall, lower half to hang in.

-- Empty bracket for suspension lead over the axle assembly on LEFT in driving directional.


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Hydraulic, internal pendulum bearing steel tailgate (with chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve for the front lifting cylinder.
With pendulum function combined with 2-hook locking

- additional. For rollerblades heavily cranked tarpaulins are required (see PL00250 or PL00260)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7-pin. White (without pushbutton switch installation in truck / tractor) incl. Emergency function via EBS with touch switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function.


Hydraulic, external pendulum bearing steel tailgate (without chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve on the front lift cylinder.
With pendulum function combined with 2-hook locking.

- additional. For rollerblades heavily cranked tarpaulins are required (see PL00250 or PL00260)
- possibly with rubber seal (see No. RW11520)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7-pin. White (without pushbutton switch installation in truck / tractor) incl. Emergency function via EBS with touch switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function.


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box



Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- Recommended for road milling insert!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

-ATTENTION: limited color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roller switch between chassis and trough.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting bottom center on the rear flap.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions approx. 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2-SR06 ISO-R

Total weight:31.000 kg
Empty weight:ca. 5.727 kg
Base data:
Total weight:31.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:20.000 kg
Empty weight:ca. 5.727 kg
Payload:ca. 26.398 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-06) with standard frame height, wheelbase approx. 4,060 mm, axle distance 1,810 mm suitable for 2-A-tractor unit equipment.


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device



without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor unit equipment must be prepared / unlocked it).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


Tires 425/65 R 22.5 TL 165 K Goodyear KMAX T M + S (regional profile).


Steel-rims 13,00x22,5 10-hole ET 0 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Additional flaps mounted on the mudguard of the first axle.


Plastic chock with bracket.



Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Bracket on the chassis longitudinal beam on LEFT in driving directional.


HYVA-high / low pressure front lift cylinder, about 5,030 mm stroke (about 75 liters of oil demand), operating pressure 170 to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet "brushed" (unpainted)


WITHOUT temperature measuring sensors and cabeling for digital measurement technology (there are, however, empty tubes for later installation)


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


Paneling of insulation (unpainted).


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


REISCH- driving jacket


RHKS chassis (2-06) with standard frame height, wheelbase approx. 4,060 mm, axle distance 1,810 mm suitable for 2-A-tractor unit equipment.

"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-06) with HIGH frame height for ASH debited from about 1270-1360 mm, wheelbase approx 4,060 mm Axle distance 1,810 mm fits on 2-A-Tractor unit equipment.

- the specified semi-trailer height range applies only to tires 425/65 R 22,5. Depending on the desired axis type and tires, the fifth wheel may change and may make unnecessary a high frame. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-06) with EXTRA HIGH frame height for ASH debited from about 1370-1420 mm, wheelbase approx 4,060 mm Wheelbase 1,810 mm fits on 2-A-Tractor unit equipment

- Required in extem highly constructed fifth wheel or tractor with caddy assembly
- The specified Aufsattelhöhenbereich applies only to tires 425/65 R 22.5. Depending on the desired axis type and tires, the fifth wheel can change and do not necessary possibly an extra high frame. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.


Jost gearbox support winch with T-foot CENTER mounted on the vehicle (only for empty seats).



(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x BPW-11-to-axles (ET 0 mm) for 22.5 "-E tires with drum brake 420 x 200 mm and handlebar springs 100/57 mm.


2 x BPW-10-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-adhesive baffles and 100/57 mm handlebars.


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis on LEFT in driving directional.


2-sided axle lift for 10/11-to-axle on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. white (without pushbutton and switch installation in trucks / tractors)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

- Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor unit equipment must be prepared / unlocked it).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

-for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation axle lift / Anfarhilfe on the trailer; Adjusting the brake pressure at finisher brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

-for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation axle lift / Anfarhilfe on the trailer; Adjusting the brake pressure at finisher brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor unit equipment).
- In addition we recommend KNORR-TIM (s.Art number BR02100.) Or WABCO SMARTBOARD (s.Art number BR02120.) For setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation axle lift / Anfarhilfe on the trailer; Adjusting the brake pressure at finisher brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Loadingmanometer (0-10 bar)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.


Tires 385/65 R 22,5 TL 160 K Aeolus AGC28 M + S (coarse construction site profile).


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (s.Art no. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (s.Art no. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting Kippzylinderlagerung below (2 SMST.)
- Front lifting Kippzylinderlagerung above (2 SMST.)
- Tilting shaft rear (4 SMST.)
- 2-hook linkage lock (6 SmSt.)


PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Mounting on the axle assembly in FR RIGHT.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please Specify exactly!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on right in driving directional


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on Right in driving directional


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 6,500 / 1,450 mm (with internal tailgate without chute)

-Volume then approx. 19,7 m?


Stainless steel sheet cladding "bright annealed" KSM70 bright (unpainted).


Stainless steel sheet panel painted in surface paint.


PREPARING for digital measurement technology incl. 4 temperature measuring sensors on the side walls and cabling.


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT or RIGHT in driving directional.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box



Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- Recommended for road milling insert!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

-ATTENTION: limited color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roller switch between chassis and trough.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Paneling of the insulation varnished in mounting color.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting bottom center on the rear flap.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions approx. 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2G-SR06

Total weight:31.000 kg
Empty weight:ca. 6.410 kg
Base data:
Total weight:31.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:20.000 kg
Empty weight:ca. 6.410 kg
Payload:ca. 25.253 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2G-06) with standard frame height 2-fold offset for bogie force steering, wheelbase approx. 4,070 mm,axle distance 1,810 mm, 1,200 mm frame width, suitable for 2-A-tractors.unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device



Mechanical "TRIDEC" -2-bar bogie forced steering on 2nd axle.


without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


Tires 425/65 R 22.5 TL 165 K Goodyear KMAX T M + S (regional profile).


Steel-rims 13,00x22,5 10-hole ET 0 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Additional flaps mounted on the mudguard of the first axle.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


HYVA-High-pressure front lifting cylinder, approx. 5.405 mm stroke (approx. 80 l oil requirement), operating pressure max. 250 bar, 1st stage hard chrome plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 6.600 / 1.450 mm (with internal tailgate with chute).


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Internal steel pendulum tailgate (with chute).


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


REISCH- driving jacket


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.


Jost gearbox support winch with T-foot CENTER mounted on the vehicle (only for empty seats).


(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


High axle set height for 2-A compact rear tipping ram with forced steering at a loaded height of up to 1,330 to 1,400 mm.


2 x BPW-11-to-axles (ET 0 mm) for 22.5 "-E tires with drum brake 420 x 200 mm and handlebar springs 100/57 mm.


2 x BPW-10-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-adhesive baffles and 100/57 mm handlebars.


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Installation on 2nd axle in on LEFT in driving directional


2-sided axle lift for 10/11-to-axle on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Installation on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Installation on RIGHT on driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Loadingmanometer (0-10 bar)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.


Tires 385/65 R 22,5 TL 160 K Aeolus AGC28 M + S (coarse construction site profile).


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)



PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Installation above the axle assembly on RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Please specify the length of the towing cable.


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 6.600 / 1.550 mm (with internal tailgate with chute).

-Volume then approx. 21,5 m?


Steel round trough 6.600 / 1.650 mm (with internal tailgate with chute).

- Volume then approx. 23 m?


Steel round trough 7.000 / 1.450 mm (with external tailgate without ladder).

-Volume then approx. 21 m?


Steel round trough 7.000 / 1.550 mm (with external tailgate without ladder).

-Volume then approx. 22,7 m?


Steel round trough 7.000 / 1.650 mm (with external tailgate without chute).

- Volume then approx. 24,3 m?


Steel round trough 7.100 / 1.450 mm (with external hydraulical tailgate without ladder).

-Volume then approx. 20,9 m?


Steel round trough 7.100 / 1.550 mm (with external hydraulical tailgate without ladder).

-Volume then approx. 22,8 m?


Steel round trough 7.100 / 1.650 mm (with external hydraulical tailgate without ladder).

- Volume then approx. 24,5 m?


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

- Mounting on LEFT or RIGHT.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


Ascent ladder divided at the side wall on LEFT in driving directional. Upper half firmly screwed to dump side wall, lower half to hang in.

- Empty bracket for suspension lead over the axle assembly on LEFT in driving directional.


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Hydraulic, internal pendulum bearing steel tailgate (with chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve for the front lifting cylinder.
With pendulum function combined with 2-hook locking

- additional. For rollerblades heavily cranked tarpaulins are required (see PL00250 or PL00260)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7-pin. white (without pushbutton and switch installation in trucks / tractors) incl. emergency function via EBS with tactile switch on the chassis.
- Power to the tailgate open: via EBS with switch on the chassis to disable the hydraulic function.


Hydraulic, external pendulum bearing steel tailgate (without chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve on the front lift cylinder.
With pendulum function combined with 2-hook locking.

- additional. at Rollplane Heavily cranked plan stops required (s.Art no. PL00250 od. PL00260)
- possibly with rubber seal (see No. RW11520)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7-pin. white (without pushbutton and switch installation in trucks / tractors) incl. emergency function via EBS with tactile switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function.


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box



Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- Recommended for road milling insert!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- Lateral to the end wall. extendable folding ladder (s.Art no. ST10900)
- Aluminum ladder 3,500 mm with hook (s.Art number FZ02360.)
- Shared access ladder on the left side wall (s.Art number SW19100.) - At ISOTEXX not possible!
- Ladder to Schiebeverdeck-guard left (no entry point) (s.Art No. ST10850.)
- Additional truck / tractor cable kit recommended (s.Art number SV04120.)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- Lateral to the end wall. extendable folding ladder (s.Art no. ST10900)
- Aluminum ladder 3,500 mm with hook (s.Art number FZ02360.)
- Shared access ladder on the left side wall (s.Art number SW19100.) - At ISOTEXX not possible!
- Ladder to Schiebeverdeck-guard left (no entry point) (s.Art No. ST10850.)
- Additional truck / tractor cable kit recommended (s.Art number SV04120.)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump.


















- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump..


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions: approx. 3,000 mm x 730 mm


Customers-markings acc. to delivered pattern


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2-AR07

Total weight:32.000 kg
Empty weight:ca. 4.410 kg
Base data:
Total weight:32.000 kg
Front weight/Support load:14.000 kg
Rear weight/Axel load:18.000 kg
Empty weight:ca. 4.410 kg
Payload:ca. 28.202 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-07) with standard frame height, wheelbase 5,000 mm,axle distance 1,310 mm suitable for 3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Removable side protection according to EC directives.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


2 x SAF-9-to-axles (ET 120 mm) for 22.5 "-E tires, INTRADISC with large AIRVENT disc brakes Ø = 430 mm in CD version (OFFROAD).


without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor unit equipment for axle load indication in the driver's cab (truck / tractor unit equipment must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving direction..


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Alu-round trough 7.300 / 1.550 mm (with internal tailgate with chute).


Floor made of 8 mm aluminum sheet.


Alu front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional


Dump walls made of 6 mm aluminum sheet.


Internal ALU pendulum tailgate with 2 vertical reinforcing frames (with chute).


Aluminum wear plate 4 mm thick at aluminum tailgate at the bottom, transversely over about 300 mm high.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


1 chassis with 3-layer-painting incl. additional zinc-rich primer


chassis 1-colour in standard black-grey.


Side protection in chassis color.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (2-07) HEAVY-DUTY (RETRO) with standard frame height, wheelbase 5.000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-07) with frame height for ASH loads from approx. 1,330 to 1,400 mm, wheelbase 5,000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-07) with EXTRA HIGH height for ASH loads from approx. 1.410 mm, wheelbase 5.000 mm, center distance 1,310 mm to 3-A-tractor unit equipment

- required for an extremely high-mounted semi-trailer coupling or for tractor with a swivel-mounted body
- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.



(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).



- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x SAF-9-to-axles (ET 0 mm) for 22.5 "-E-Tires INTRADRUM with drum brake 420 x 180 mm in CD version (OFFROAD).



2 x SAF-9-to-axle (ET 120 mm) for 22.5 "-E tires, INTRADISC with large INTEGRAL disc brakes Ø = 430 mm in CD version (OFFROAD).



2 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


2 x BPW-9-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-service brakes, as well as reinforced axle body and reinforced 1-leaf control springs 70/62 mm OFFROAD).


2 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Installation on 2nd axle on LEFT driving direction


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


2-sided axle lift for 9-to-axis on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck /Tractor unit equipment)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Installation on RIGHT in driving direction,


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Installation on RIGHT in driving direction,


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor unit eqipment for axle load indication in the driver's cab (truck / tractor unit equipment must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor unit equipment).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


Electro-cabling acc. to GGVS/ADR with electro-connection front 15-pol.


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.


spare tire 385/65 R 22,5 TL 160 K.

- Our choice on STEEL-RINGS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


Steel-rims 13,00x22,5 10-hole ET 0 mm.


Steel-rims 13,00x22,5 10-hole ET 12 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


1 piece PVC-tool kit approx. 800 x 500 x 500 mm (WxHxD), lockable. 230,00 €15,0 kg

- Installation in front of the axle unit on LEFT in driving direction.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving direction.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Please specify the length of the towing cable.


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving direction,


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Alu-round trough 7.300 / 1.450 mm (with internal tailgate with chute).


Alu-round trough 7.300 /1,650 mm (with internal tailgate with chute).

-Volume then approx. 25,6 m?


Alu-round trough 7.600 / 1.450 mm (with Outside Rear hatch without chute).

-volume then approx .23 m?


Alu-round trough 7.600 / 1.550 mm (with Outside Rear hatch without chute).

-Volume then approx.24,8 m?


Alu-round trough 7.600 / 1.650 mm (with Outside Rear hatch without chute).

-Volumen then approx.26,6m?


Floor made of 6 mm aluminum sheet.

- absolutely necessary some kind of wear floor!


General remarks on wearing floors:


Steel wear floor made of 4 mm QSTE 690.


Steel wear floor made of 3 mm HB 450.


Steel wear floor made of 4 mm HB 450.


Steel wear floor made of 5 mm HB 450.


Aluminum wear base made of 4 mm aluminum sheet.


Aluminum wear base made of 5 mm aluminum sheet


Aluminum wear base made of 6 mm aluminum sheet.


STAINLESS STEEL wear floor 3 mm thick in the rear area over 2.5 mtr. Length screwed with trough.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

- Installation on LEFT and RIGHT .


dump wall made of 5 mm aluminum sheet.


Ascent ladder divided at the side wall on LEFT in driving directional. Upper half firmly screwed to dump side wall, lower half to hang in.

- Empty bracket for suspension lead over the axle assembly in FR LEFT.


- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box




Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- recommended for road milling!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor unit equipment cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydraulics smear (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Installation at the center of the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Top mounting at the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions: approx. 3,000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2-AR07 ISO-R

Total weight:32.000 kg
Empty weight:ca. 4.882 kg
Base data:
Total weight:32.000 kg
Front weight/Support load:14.000 kg
Rear weight/Axel load:18.000 kg
Empty weight:ca. 4.882 kg
Payload:ca. 28.202 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-07) with standard frame height, wheelbase 5,000 mm,axle distance 1,310 mm suitable for 3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Removable side protection according to EC directives.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


2 x SAF-9-to-axles (ET 120 mm) for 22.5 "-E tires, INTRADISC with large AIRVENT disc brakes Ø = 430 mm in CD version (OFFROAD).


without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor unit equipment for axle load indication in the driver's cab (truck / tractor unit equipment must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.



Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving direction..


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Alu-round trough 7.300 / 1.550 mm (with internal tailgate with chute).


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet "brushed" (unpainted)


WITHOUT temperature measuring sensors and cabeling for digital measurement technology (there are, however, empty tubes for later installation)


Floor made of 8 mm aluminum sheet.


Alu front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional


Dump walls made of 6 mm aluminum sheet.


Internal ALU pendulum tailgate with 2 vertical reinforcing frames (with chute).


Aluminum wear plate 4 mm thick at aluminum tailgate at the bottom, transversely over about 300 mm high.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


1 chassis with 3-layer-painting incl. additional zinc-rich primer


chassis 1-colour in standard black-grey.


Side protection in chassis color.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


Paneling of insulation (unpainted).


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (2-07) HEAVY-DUTY (RETRO) with standard frame height, wheelbase 5.000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-07) with frame height for ASH loads from approx. 1,330 to 1,400 mm, wheelbase 5,000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-07) with EXTRA HIGH height for ASH loads from approx. 1.410 mm, wheelbase 5.000 mm, center distance 1,310 mm to 3-A-tractor unit equipment

- required for an extremely high-mounted semi-trailer coupling or for tractor with a swivel-mounted body
- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.



(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).



- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x SAF-9-to-axles (ET 0 mm) for 22.5 "-E-Tires INTRADRUM with drum brake 420 x 180 mm in CD version (OFFROAD).


2 x SAF-9-to-axle (ET 120 mm) for 22.5 "-E tires, INTRADISC with large INTEGRAL disc brakes Ø = 430 mm in CD version (OFFROAD).



2 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


2 x BPW-9-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-service brakes, as well as reinforced axle body and reinforced 1-leaf control springs 70/62 mm OFFROAD).


2 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Installation on 2nd axle on LEFT driving direction


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


2-sided axle lift for 9-to-axis on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck /Tractor unit equipment)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Installation on RIGHT in driving direction,


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Installation on RIGHT in driving direction,


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor unit eqipment for axle load indication in the driver's cab (truck / tractor unit equipment must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor unit equipment).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


Electro-cabling acc. to GGVS/ADR with electro-connection front 15-pol.


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.


spare tire 385/65 R 22,5 TL 160 K.

- Our choice on STEEL-RINGS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


Steel-rims 13,00x22,5 10-hole ET 0 mm.


Steel-rims 13,00x22,5 10-hole ET 12 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


1 piece PVC-tool kit approx. 800 x 500 x 500 mm (WxHxD), lockable. 230,00 €15,0 kg

- Installation in front of the axle unit on LEFT in driving direction.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving direction.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Please specify the length of the towing cable.


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving direction,


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Alu-round trough 7.300 / 1.450 mm (with internal tailgate with chute).


Alu-round trough 7.300 /1,650 mm (with internal tailgate with chute).

-Volume then approx. 25,6 m?


Alu-round trough 7.600 / 1.450 mm (with Outside Rear hatch without chute).

-volume then approx .23 m?


Alu-round trough 7.600 / 1.550 mm (with Outside Rear hatch without chute).

-Volume then approx.24,8 m?


Alu-round trough 7.600 / 1.650 mm (with Outside Rear hatch without chute).

-Volumen then approx.26,6m?


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet cladding "bright annealed" KSM70 bright (unpainted).


Stainless steel sheet panel painted in surface paint.


PREPARING for digital measurement technology incl. 4 temperature measuring sensors on the side walls and cabling.


Floor made of 6 mm aluminum sheet.

- absolutely necessary some kind of wear floor!


General remarks on wearing floors:


Steel wear floor made of 4 mm QSTE 690.


Steel wear floor made of 3 mm HB 450.


Steel wear floor made of 4 mm HB 450.


Steel wear floor made of 5 mm HB 450.


Aluminum wear base made of 4 mm aluminum sheet.


Aluminum wear base made of 5 mm aluminum sheet


Aluminum wear base made of 6 mm aluminum sheet.


STAINLESS STEEL wear floor 3 mm thick in the rear area over 2.5 mtr. Length screwed with trough.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

- Installation on LEFT and RIGHT .


dump wall made of 5 mm aluminum sheet.


OUTDOOR ALU pendulum tailgate with 2 vertical reinforcing frames (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of Schütte - can have a negative impact on the final use!
- additional. Clamping closures required (see No. RW11540)
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box


Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- recommended for road milling!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor unit equipment cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydraulics smear (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Paneling of the insulation varnished in mounting color.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Installation at the center of the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Top mounting at the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions: approx. 3,000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2-AK07

Total weight:32.000 kg
Empty weight:ca. 4.755 kg
Base data:
Total weight:32.000 kg
Front weight/Support load:14.000 kg
Rear weight/Axel load:18.000 kg
Empty weight:ca. 4.755 kg
Payload:ca. 28.013 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-07) with standard frame height, wheelbase 5,000 mm,axle distance 1,310 mm suitable for 3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Removable side protection according to EC directives.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device



2 x SAF-9-to-axles (ET 120 mm) for 22.5 "-E tires, INTRADISC with large AIRVENT disc brakes Ø = 430 mm in CD version (OFFROAD).


without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on left in driving directional.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


aluminium square box body 7.320 / 1.350 mm.


Aluminum lower belts with 45 °floor slope from the side gate to the to the floor.


Floor front 2/3 from 6 mm, rear 1/3 from 7 mm aluminum- sheet


Alu front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

-Ascent indriving directional LEFT and RIGHT.


Dump walls made of REINFORCED aluminum hollow profiles 40/4/2 mm thick with aluminum upper profile profiles projecting inwards.
.


Internal ALU pendulum tailgate with lateral rubber seal (with poured).


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


1 chassis with 3-layer-painting incl. additional zinc-rich primer


chassis 1-colour in standard black-grey.


Side protection in chassis color.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (2-07) HEAVY-DUTY (RETRO) with standard frame height, wheelbase 5.000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-07) with frame height for ASH loads from approx. 1,330 to 1,400 mm, wheelbase 5,000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-07) with EXTRA HIGH height for ASH loads from approx. 1.410 mm, wheelbase 5.000 mm, center distance 1,310 mm to 3-A-tractor unit equipment

- required for an extremely high-mounted semi-trailer coupling or for tractor with a swivel-mounted body
- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.



(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x SAF-9-to-axles (ET 0 mm) for 22.5 "-E-Tires INTRADRUM with drum brake 420 x 180 mm in CD version (OFFROAD).


2 x SAF-9-to-axle (ET 120 mm) for 22.5 "-E tires, INTRADISC with large INTEGRAL disc brakes Ø = 430 mm in CD version (OFFROAD).



2 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


2 x BPW-9-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-service brakes, as well as reinforced axle body and reinforced 1-leaf control springs 70/62 mm OFFROAD).


2 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


Hubodometer Axis Cap kilometer counterr MECHANICAL.

-Installation on 2.axle on left in Driving directionl


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


2-sided axle lift for 9-to-axis on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

- Assembly in the right driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Assembly in the right driving directional


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied,


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Loadingmanometer (0-10 bar)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- According to Our choice on STEEL-RINGS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


Steel-rims 13,00x22,5 10-hole ET 0 mm.


Steel-rims 13,00x22,5 10-hole ET 12 0 mm.


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)
- 4-hook linkage locking pneumatic. Or only mechanical (2 SmSt.)


1 piece PVC-tool kit approx. 800 x 500 x 500 mm (WxHxD), lockable. 230,00 €15,0 kg

- Installation in front of the axle unit on left in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on left in driving directional


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Please specify the length of the towing cable.


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the bottom of the tray on right in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the dump of the tray on right in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on chassis longitudinal beam on RIGHT in driving directional.


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


aluminium square box body 7.320 / 1.450 mm.

- Volume then approx. 26 m?


aluminium square box body 7.320 / 1.550 mm.

-Volume then approx. 27,8 m?


aluminium square box body 7.320 / 1.650 mm.

-Volume then approx 29,6 m?


aluminium square box body 7.320 / 1.750 mm.

-Volume then approx. 31,4 m?


aluminium square box body 7.320 / 1.850 mm.

- Volume then approx 33,2 m?


aluminium square box body 7.320 / 1.950 mm.

-Volume then approx 35 m?


aluminium square box body 7.620 / 1.350 mm.

-Volume then approx. 25,2 m?


aluminium square box body 7.620 / 1.450 mm.

-volume then approx. 27,1 m?


aluminium square box body 7.620 / 1.550 mm.

-Volume then approx. 28,9 m?


aluminium square box body 7.620 / 1.650 mm.

-Volume then approx. 30,8 m?


aluminium square box body 7.620 / 1.750 mm.

- volume then approx. 32,7 m?


aluminium square box body 7.620 / 1.850 mm.

- Volume then approx. 35,5 m?


Profile joints welded in to side / back gate over entire height


Dump trough prepared for underwater heating by means of exhaust gases (WITHOUT funnel and no truck part).


Dump designed for underwater heating with connecting funnel using exhaust gases (without truck part).


Mulde designed for underwater heating with connecting funnel using exhaust gases (without truck part).


Aluminum lower belts with 90 °floor angle from the side gate to the floor


Floor front 2/3 of 5 mm, rear 1/3 of 6 mm aluminum sheet


Floor from 7 mm aluminium sheet.


Floor front 2/3 from 7 mm, rear 1/3 from 8 mm aluminum sheet.


Floor front 2/3 from 7 mm, rear 1/3 from 10 mm aluminum sheet.


Floor front 2/3 from 7 mm, rear 1/3 from 10 mm aluminum sheet (including compensating wear plates on the lower straps in the area of ??the 10 mm floor).

- ATTENTION: Competitor's products do not have any compensating wear plates!


floor from 8 mm aluminium sheet


Floor from 10 mm aluminium sheet


Floor in 10 mm aluminium sheet (Including compensating wear plates on the lower straps).

- ATTENTION: Competitor's products do not have any compensating wear plates!


Foldable Lashing eyes recessed in the aluminum floor.

- ATTENTION: Aluminum lower chord with 90 ° ground angle required (see part no. BO01110)
- Distribution: 1. pair approx. 500 mm from front gate; Last pair about 500 mm inside rear gate, rest equally divided.


General remarks on wearing floors:


Steel wear floor made of 4 mm QSTE 690,,Sideways about approx. 200 mm raised


Steel wear floor made of 3 mm HB 450 ,Sideways about approx. 200 mm raised


Steel wear base made of 4 mm HB 450,Sideways about approx. 200 mm raised


Aluminum wear-resistant base made of 4 mm aluminum sheet, Laterally raised over bevel


Aluminum wear-resistant base made of 5 mm aluminum sheet, Laterally raised over bevel


Webac electric vibrator (vibrator) mounted on the bottom of the dump .


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

- Installation on LEFT and RIGHT in driving directional.


Dump walls made of aluminum hollow profiles 40/3/2 mm thick with aluminum upper profile profiles projecting inwards.


Alu wear plates 4 mm thick at the Dump rear side walls (approx. 2,500 mm long, front approx. 250 mm and rear approx. 900 mm high) from AlMg 4,5 Mn W28.


Alu wear plates 5 mm thick at the rear side walls (approx. 2,500 mm long, front approx. 250 mm and rear approx. 900 mm high) from AlMg 4,5 Mn W28.


OUTDOOR ALU pendulum tailgate 17 ° diagonally with surrounding rubber seal (without chute).


OUTDOOR ALU pendulum tailgate 5 ° oblique with surrounding rubber seal (without chute).

- additional. Clamping closures required (see No. RW11540)


OUTDOOR ALU pendulum tailgate 5 ° oblique with surrounding rubber seal (without chute).


Aluminum wear plate 4 mm thick at aluminum tailgate at the bottom, transversely over about 300 mm high.


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Edge protection at the top of the tailgate by means of a stainless steel angle riveted between the pendulum bearings 100x100x5 mm.


Automatic 4-hook rear panel locking with return spring and additional Manual spring lock fuse.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.



.Grain slider rear in back wall with hand lever and cover box ..


Steel cover plate inside grain feeder for protection from coarse bulk materials, can be operated from the outside.




Without crossbow.


steel ?round tube-cross bow (Ø = ca. 50 mm) TELESKOPIERBAR with tension lock and bearing at top boom.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- ATTENTION: pay attention to the total height !!
- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- ATTENTION: pay attention to the total height !!
- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Installation at the center of the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

-Installation at top center of the tailgate



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

-Dimensions: approx. 3,000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2-SR07

Total weight:32.000 kg
Empty weight:ca. 5.465 kg
Base data:
Total weight:32.000 kg
Front weight/Support load:14.000 kg
Rear weight/Axel load:18.000 kg
Empty weight:ca. 5.465 kg
Payload:ca. 27.153 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-07) with standard frame height, wheelbase 5,000 mm,axle distance 1,310 mm suitable for 3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Removable side protection according to EC directives.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


2 x SAF-9-to-axles (ET 120 mm) for 22.5 "-E tires, INTRADISC with large AIRVENT disc brakes Ø = 430 mm in CD version (OFFROAD).


without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional..


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 7,300 / 1,550 mm (with internal tailgate with chute

-Volume then approx. 24m?


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Internal steel pendulum tailgate (with chute).


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


Side protection in chassis color.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (2-07) HEAVY-DUTY (RETRO) with standard frame height, wheelbase 5.000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

-"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-07) with frame height for ASH loads from approx. 1,330 to 1,400 mm, wheelbase 5,000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

- The specified Aufsattelhöhenbereich applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!









Google ÜbersetzerSofortübersetzung deaktivieren










Englisch

Deutsch

Französisch


Sprache erkennen









Deutsch

Englisch

Französisch













- der angegebene Aufsattelhöhenbereich bezieht sich nur auf Bereifung 385/65 R 22,5. Je nach gewünschten Achsentyp und Bereifung können sich die Aufsattelhöhen verändern und evtl. einen hohen Rahmen nicht notwendig machen. Wir bitten und genaue Angabe der UNBELASTETEN UND BELASTETEN LKW-Aufsattelhöhe!




























- The specified Aufsattelhöhenbereich applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-07) with EXTRA HIGH height for ASH loads from approx. 1.410 mm, wheelbase 5.000 mm, center distance 1,310 mm to 3-A-tractor unit equipment

- required for an extremely high-mounted semi-trailer coupling or for tractor with a swivel-mounted body
- The specified Aufsattelhöhenbereich applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x SAF-9-to-axles (ET 0 mm) for 22.5 "-E-Tires INTRADRUM with drum brake 420 x 180 mm in CD version (OFFROAD).



2 x SAF-9-to-axle (ET 120 mm) for 22.5 "-E tires, INTRADISC with large INTEGRAL disc brakes Ø = 430 mm in CD version (OFFROAD).



2 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


2 x BPW-9-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-service brakes, as well as reinforced axle body and reinforced 1-leaf control springs 70/62 mm OFFROAD).


2 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


Hubodometer Axis Cap kilometer counterr MECHANICAL.

-Mounting on 2nd axle on LEFT in driving directional


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


2-sided axle lift for 9-to-axis on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)


2-sided axle lift for 10/11-to-axle on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Round Full-LED-3-chamber-rear lights double (1x 5021908 / 1x 5021911) incl.. LED Blinker failure control (5019685), 2 round rear fog-/reversing-lights (5020731) and 2 separate triangle- retro reflectors.


Additional round Full-LED-3-chamber-rear light (5021908) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

Made in our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


Steel-rims 13,00x22,5 10-hole ET 0 mm.


Steel-rims 13,00x22,5 10-hole ET 12 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axles (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


1 piece PVC-tool kit approx. 800 x 500 x 500 mm (WxHxD), lockable. 230,00 €15,0 kg

- Installation in front of the axle unit on LEFT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 7,300 / 1,450 mm (with internal tailgate with chute)


Steel round trough 7.3000 / 1.650 mm (with external tailgate with chute).

-Volume then approx. 25,6 m?


Steel round trough 7,600 / 1,450 mm (with internal tailgate without chute)

- volume then approx. 23 m?


Steel round trough 7,600 / 1,550 mm (with internal tailgate without chute

-Volume then approx. 24,8 m?


Steel round trough 7,600 / 1,650 mm (with internal tailgate without chute

-Volume then approx. 26,6 m?


Steel round trough 7,600 / 1,750 mm (with internal tailgate without chute

- Volume then approx 28,3 m?


Steel round trough 7,600 / 1,850 mm (with internal tailgate without chute

-Volume then approx 30,2 m?


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Webac electric vibrator (vibrator) mounted on the bottom of the dump .


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional,


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Hydraulic, internal pendulum bearing steel tailgate (with chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve for the front lifting cylinder.
With pendulum function combined with 2-hook locking

-- additional. For rollerblades heavily cranked tarpaulins are required (see PL00250 or PL00260)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7-pin. White (without pushbutton switch installation in truck / tractor) incl. Emergency function via EBS with touch switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function.


Hydraulic, external pendulum bearing steel tailgate (without chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve on the front lift cylinder.
With pendulum function combined with 2-hook locking.

- additional. For rollerblades heavily cranked tarpaulins are required (see PL00250 or PL00260)
- possibly with rubber seal (see No. RW11520)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7-pin. White (without pushbutton switch installation in truck / tractor) incl. Emergency function via EBS with touch switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function.


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box



Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: limited color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump..


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

-- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions: approx. 3,000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-2-SR07 ISO-R

Total weight:32.000 kg
Empty weight:ca. 6.012 kg
Base data:
Total weight:32.000 kg
Front weight/Support load:14.000 kg
Rear weight/Axel load:18.000 kg
Empty weight:ca. 6.012 kg
Payload:ca. 27.153 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (2-07) with standard frame height, wheelbase 5,000 mm,axle distance 1,310 mm suitable for 3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Removable side protection according to EC directives.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


2 x SAF-9-to-axles (ET 120 mm) for 22.5 "-E tires, INTRADISC with large AIRVENT disc brakes Ø = 430 mm in CD version (OFFROAD).


without axle lift.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.



Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional..


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 7,300 / 1,550 mm (with internal tailgate with chute

-Volume then approx. 24m?


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet "brushed" (unpainted)


WITHOUT temperature measuring sensors and cabeling for digital measurement technology (there are, however, empty tubes for later installation)


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Internal steel pendulum tailgate (with chute).


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


Side protection in chassis color.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


Paneling of insulation (unpainted).


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (2-07) HEAVY-DUTY (RETRO) with standard frame height, wheelbase 5.000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

-"STABILITY OF THAT, TECHNIQUE OF TODAY"


RHKS chassis (2-07) with frame height for ASH loads from approx. 1,330 to 1,400 mm, wheelbase 5,000 mm, center distance 1,310 mm suitable for 3-A-tractor unit equipment

- The specified Aufsattelhöhenbereich applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!









Google ÜbersetzerSofortübersetzung deaktivieren










Englisch

Deutsch

Französisch


Sprache erkennen









Deutsch

Englisch

Französisch













- der angegebene Aufsattelhöhenbereich bezieht sich nur auf Bereifung 385/65 R 22,5. Je nach gewünschten Achsentyp und Bereifung können sich die Aufsattelhöhen verändern und evtl. einen hohen Rahmen nicht notwendig machen. Wir bitten und genaue Angabe der UNBELASTETEN UND BELASTETEN LKW-Aufsattelhöhe!




























- The specified Aufsattelhöhenbereich applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (2-07) with EXTRA HIGH height for ASH loads from approx. 1.410 mm, wheelbase 5.000 mm, center distance 1,310 mm to 3-A-tractor unit equipment

- required for an extremely high-mounted semi-trailer coupling or for tractor with a swivel-mounted body
- The specified Aufsattelhöhenbereich applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.



(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


2 x SAF-9-to-axles (ET 0 mm) for 22.5 "-E-Tires INTRADRUM with drum brake 420 x 180 mm in CD version (OFFROAD).


2 x SAF-9-to-axle (ET 120 mm) for 22.5 "-E tires, INTRADISC with large INTEGRAL disc brakes Ø = 430 mm in CD version (OFFROAD).



2 x BPW-9-to-axles (ET 0 mm) for 22.5 "-E tires with drum brakes 420 x 180 mm, as well as reinforced axle body and reinforced 1-leaf spring bar 70/62 mm (OFFROAD).


2 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


2 x BPW-9-to-axles (ET 0 mm) for 22.5 "-E tires with large disc brakes Ø = 430 mm including self-service brakes, as well as reinforced axle body and reinforced 1-leaf control springs 70/62 mm OFFROAD).


2 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


Hubodometer Axis Cap kilometer counterr MECHANICAL.

-Mounting on 2nd axle on LEFT in driving directional


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


2-sided axle lift for 9-to-axis on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)


2-sided axle lift for 10/11-to-axle on 1st axle controlled by EBS, electrically operated from the driver's cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- for reading KM level, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake lining wear indicator for disc brakes at 2 axles on ABS / EBS warning indicator in the driver's cab..


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure when the brake is applied, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Tire pressure control system acting on 4 wheels (Wabco-IVTM) with indicator in the tractor (if it is suitable for this purpose) and on the Smart-Board (if fitted in the trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.


spare tire 385/65 R 22,5 TL 160 K.

Made in our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


Steel-rims 13,00x22,5 10-hole ET 0 mm.


Steel-rims 13,00x22,5 10-hole ET 12 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axles (0 SmSt.)
- Steering Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


1 piece PVC-tool kit approx. 800 x 500 x 500 mm (WxHxD), lockable. 230,00 €15,0 kg

- Installation in front of the axle unit on LEFT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 7,300 / 1,450 mm (with internal tailgate with chute)


Steel round trough 7.3000 / 1.650 mm (with external tailgate with chute).

-Volume then approx. 25,6 m?


Steel round trough 7,600 / 1,450 mm (with internal tailgate without chute)

- volume then approx. 23 m?


Steel round trough 7,600 / 1,550 mm (with internal tailgate without chute

-Volume then approx. 24,8 m?


Steel round trough 7,600 / 1,650 mm (with internal tailgate without chute

-Volume then approx. 26,6 m?


Steel round trough 7,600 / 1,750 mm (with internal tailgate without chute

- Volume then approx 28,3 m?


Steel round trough 7,600 / 1,850 mm (with internal tailgate without chute

-Volume then approx 30,2 m?


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet cladding "bright annealed" KSM70 bright (unpainted).


Stainless steel sheet panel painted in surface paint.


PREPARING for digital measurement technology incl. 4 temperature measuring sensors on the side walls and cabling.


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional,


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box


Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- Recommended for road milling insert!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: limited color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump..


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Paneling of the insulation varnished in mounting color.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

-- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions: approx. 3,000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-AR07

Total weight:35.000 kg
Empty weight:ca. 5.000 kg
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 5.000 kg
Payload:ca. 30.876 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-07) with standard frame height, wheelbase 4.640 mm, axle spacing 1.310 / 1.310 mm suitable for 2-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

-with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Bracket on the chassis longitudinal beam on LEFT in driving directional


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Alu-round trough 7.300 / 1.550 mm (with internal tailgate with chute).

- volume then approx. 24 m?


Floor made of 8 mm aluminum sheet.


Alu front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Dump walls made of 6 mm aluminum sheet.


Internal ALU pendulum tailgate with 2 vertical reinforcing frames (with chute).


Aluminum wear plate 4 mm thick at aluminum tailgate at the bottom, transversely over about 300 mm high.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


1 chassis with 3-layer-painting incl. additional zinc-rich primer


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (3-07) HEAVY-DUTY (RETRO) with standard frame height ,wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm suitable for 2-A tractor.

" STABILITY of that time. TECHNOLOGY of Today"


RHKS chassis (3-07) with HHH frame height for ASH loads from approx. 1,260 to 1,350 mm, wheelbase 4,640 mm, center distance 1,310 / 1,310 mm suitable for 2-A-tractor unit equipment.

- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (3-07) with EXTRA HIGH frame height for ASH debited from about 1360-1420 mm, wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm fits on 2-A-Tractor unit equipment.

- Required for an extremely high-mounted semitrailer coupling or for tractors with a swivel frame design
- the specified saddle height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the height of the trailer can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNLOADED AND LOADED truck saddle height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

-exact specification about the lowest and highest saddle height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).


3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).




SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

-Mounting on 2nd axis on LEFT in driving directional.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- In this case, the start-up assistance button must be pressed twice in succession (for this purpose, the pushbutton switch in the truck / tractor is required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

-with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)



tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Round Full-LED-3-chamber-rear lights double (1x 5021908 / 1x 5021911) incl.. LED Blinker failure control (5019685), 2 round rear fog-/reversing-lights (5020731) and 2 separate triangle- retro reflectors.


Additional round Full-LED-3-chamber-rear light (5021908) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (s.Art no. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (s.Art no. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brake axles (12 SMST.)
- Disc brakes axles (0 SmSt.)
- Self-steering axle (2 SMST.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Installation above the axle assembly RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction



Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Alu-round trough 7.300 / 1.450 mm (with internal tailgate with chute).


Alu-round trough 7.300 /1,650 mm (with internal tailgate with chute).

- volume then approx. 25,6 m?


Alu-round trough 7.600 / 1.450 mm (with Outside Rear hatch without chute).

- volume then approx. 23 m?


Alu-round trough 7.600 / 1.550 mm (with Outside Rear hatch without chute).

- volume then approx. 24,8 m?


Alu-round trough 7.600 / 1.650 mm (with Outside Rear hatch without chute).

- volume then approx. 26,6 m?


Floor made of 6 mm aluminum sheet.

- absolutely necessary some kind of wear floor!


General remarks on wearing floors:


Steel wear floor made of 4 mm QSTE 690.


Steel wear floor made of 3 mm HB 450.


Steel wear floor made of 4 mm HB 450.


Steel wear floor made of 5 mm HB 450.


Aluminum wear base made of 4 mm aluminum sheet.


Aluminum wear base made of 5 mm aluminum sheet


Aluminum wear base made of 6 mm aluminum sheet.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional


dump wall made of 5 mm aluminum sheet.


Ascent ladder divided at the side wall on LEFT in driving directional. Upper half firmly screwed to dump side wall, lower half to hang in.

- Empty bracket for suspension lead over the axle assembly on LEFT in driving directional


- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box




Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

-- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing
(s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow




REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions approx. 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-AR07 ISO-R

Total weight:35.000 kg
Empty weight:ca. 5.472 kg
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 5.472 kg
Payload:ca. 30.876 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-07) with standard frame height, wheelbase 4.640 mm, axle spacing 1.310 / 1.310 mm suitable for 2-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

-with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.



Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Bracket on the chassis longitudinal beam on LEFT in driving directional


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Alu-round trough 7.300 / 1.550 mm (with internal tailgate with chute).

- volume then approx. 24 m?


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet "brushed" (unpainted)


WITHOUT temperature measuring sensors and cabeling for digital measurement technology (there are, however, empty tubes for later installation)


Floor made of 8 mm aluminum sheet.


Alu front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Dump walls made of 6 mm aluminum sheet.


Internal ALU pendulum tailgate with 2 vertical reinforcing frames (with chute).


Aluminum wear plate 4 mm thick at aluminum tailgate at the bottom, transversely over about 300 mm high.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


1 chassis with 3-layer-painting incl. additional zinc-rich primer


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


Paneling of insulation (unpainted).


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (3-07) HEAVY-DUTY (RETRO) with standard frame height ,wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm suitable for 2-A tractor.

" STABILITY of that time. TECHNOLOGY of Today"


RHKS chassis (3-07) with HHH frame height for ASH loads from approx. 1,260 to 1,350 mm, wheelbase 4,640 mm, center distance 1,310 / 1,310 mm suitable for 2-A-tractor unit equipment.

- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (3-07) with EXTRA HIGH frame height for ASH debited from about 1360-1420 mm, wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm fits on 2-A-Tractor unit equipment.

- Required for an extremely high-mounted semitrailer coupling or for tractors with a swivel frame design
- the specified saddle height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the height of the trailer can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNLOADED AND LOADED truck saddle height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

-exact specification about the lowest and highest saddle height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).


3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).




SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

-Mounting on 2nd axis on LEFT in driving directional.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- In this case, the start-up assistance button must be pressed twice in succession (for this purpose, the pushbutton switch in the truck / tractor is required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

-with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)



tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Round Full-LED-3-chamber-rear lights double (1x 5021908 / 1x 5021911) incl.. LED Blinker failure control (5019685), 2 round rear fog-/reversing-lights (5020731) and 2 separate triangle- retro reflectors.


Additional round Full-LED-3-chamber-rear light (5021908) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (s.Art no. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (s.Art no. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brake axles (12 SMST.)
- Disc brakes axles (0 SmSt.)
- Self-steering axle (2 SMST.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Installation above the axle assembly RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction



Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Alu-round trough 7.300 / 1.450 mm (with internal tailgate with chute).


Alu-round trough 7.300 /1,650 mm (with internal tailgate with chute).

- volume then approx. 25,6 m?


Alu-round trough 7.600 / 1.450 mm (with Outside Rear hatch without chute).

- volume then approx. 23 m?


Alu-round trough 7.600 / 1.550 mm (with Outside Rear hatch without chute).

- volume then approx. 24,8 m?


Alu-round trough 7.600 / 1.650 mm (with Outside Rear hatch without chute).

- volume then approx. 26,6 m?


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet cladding "bright annealed" KSM70 bright (unpainted).


Stainless steel sheet panel painted in surface paint.


PREPARING for digital measurement technology incl. 4 temperature measuring sensors on the side walls and cabling.


Floor made of 6 mm aluminum sheet.

- absolutely necessary some kind of wear floor!


General remarks on wearing floors:


Steel wear floor made of 4 mm QSTE 690.


Steel wear floor made of 3 mm HB 450.


Steel wear floor made of 4 mm HB 450.


Steel wear floor made of 5 mm HB 450.


Aluminum wear base made of 4 mm aluminum sheet.


Aluminum wear base made of 5 mm aluminum sheet


Aluminum wear base made of 6 mm aluminum sheet.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional


dump wall made of 5 mm aluminum sheet.


OUTDOOR ALU pendulum tailgate with 2 vertical reinforcing frames (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of Schütte - can have a negative impact on the final use!
- additional. Clamping closures required (see No. RW11540)
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box


Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

-- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing
(s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Paneling of the insulation varnished in mounting color.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow




REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions approx. 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-AK07

Total weight:35.000 kg
Empty weight:ca. 5.130 kg
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 5.130 kg
Payload:ca. 30.737 kg
 
Construction:
Bridge size:
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-07) with standard frame height, wheelbase 4.640 mm, axle spacing 1.310 / 1.310 mm suitable for 2-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


aluminium square box body 7.320 / 1.350 mm.


Aluminum lower belts with 45 °floor slope from the side gate to the to the floor.


Floor front 2/3 from 6 mm, rear 1/3 from 7 mm aluminum- sheet


Alu front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

-Ascent on LEFT and RIGHT in driving directional.


Dump walls made of REINFORCED aluminum hollow profiles 40/4/2 mm thick with aluminum upper profile profiles projecting inwards.
.


Internal ALU pendulum tailgate with lateral rubber seal (with poured).


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


1 chassis with 3-layer-painting incl. additional zinc-rich primer


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (3-07) HEAVY-DUTY (RETRO) with standard frame height ,wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm suitable for 2-A tractor.

" STABILITY of that time. TECHNOLOGY of Today"


RHKS chassis (3-07) with HHH frame height for ASH loads from approx. 1,260 to 1,350 mm, wheelbase 4,640 mm, center distance 1,310 / 1,310 mm suitable for 2-A-tractor unit equipment.

- the specified semi-trailer height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We kindly ask you to specify the exact UNBELASTED AND LOADED truck height!


RHKS chassis (3-07) with EXTRA HIGH frame height for ASH debited from about 1360-1420 mm, wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm fits on 2-A-Tractor unit equipment.

- Required for an extremely high-mounted semitrailer coupling or for tractors with a swivel frame design
- the specified saddle height range applies only to tires 385/65 R 22,5. Depending on the desired axle type and tires, the height of the trailer can change and an extra high frame may not be necessary. We kindly ask you to specify the exact UNLOADED AND LOADED truck saddle height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.


Jost gearbox support winch with T-foot CENTER mounted on the vehicle (only for empty seats).




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest saddle height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).


3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).



SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis on LEFT in driving directional.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- In this case, the start-up assistance button must be pressed twice in succession (for this purpose, the pushbutton switch in the truck / tractor is required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

- Mounting on RIGHT in driving directional .


DUOMATIK- brake connection front in addition to red /yellow draw gear head

- Mounting on RIGHT in driving directional .


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- with standard availability of the axle load data via EBS modulator to tractor for axle load indication in the driver's cab (truck / tractor must be prepared / enabled for this).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMART BOARD for reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (s.Art no. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (s.Art no. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brake axles (12 SMST.)
- Disc brakes axles (0 SmSt.)
- Self Steering Axle (2 SmSt.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)
- 4-hook linkage locking pneumatic. Or only mechanical (2 SmSt.)


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the bottom of the through on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the bottom of the through on RIGHT in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving direction


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


aluminium square box body 7.320 / 1.450 mm.

-Volume then approx. 26 m?


aluminium square box body 7.320 / 1.550 mm.

-Volume then approx 27,8 m?


aluminium square box body 7.320 / 1.650 mm.

-Volume then approx. 29,6 m?


aluminium square box body 7.320 / 1.750 mm.

--Volume then approx. 31,4 m?


aluminium square box body 7.320 / 1.850 mm.

-Volume then approx. 33,2 m?


aluminium square box body 7.320 / 1.950 mm.

-Volume then approx. 35 m?


aluminium square box body 7.620 / 1.350 mm.

-Volume then approx. 25,2 m?


aluminium square box body 7.620 / 1.450 mm.

-Volume then approx. 27,1 m?


aluminium square box body 7.620 / 1.550 mm.

-Volume then approx.28,9 m?


aluminium square box body 7.620 / 1.650 mm.

-Volume then approx. 30,8 m?


aluminium square box body 7.620 / 1.750 mm.

-Volume then approx. 32,7 m?


aluminium square box body 7.620 / 1.850 mm.

-Volume then approx. 35,5 m?


aluminium square box body 7.620 / 1.950 mm.

-Volume then approx.37,4 m?


aluminium square box body 7.620 / 2.050 mm.

- Volume then approx. 39,4 m?


aluminium square box body 7.620 / 2.150 mm.

- Volume then approx. 41,4 m?


Profile joints welded in to side / back gate over entire height


Dump trough prepared for underwater heating by means of exhaust gases (WITHOUT funnel and no truck part).


Dump designed for underwater heating with connecting funnel using exhaust gases (without truck part).


Mulde designed for underwater heating with connecting funnel using exhaust gases (without truck part).


Aluminum lower belts with 90 °floor angle from the side gate to the floor


Floor front 2/3 of 5 mm, rear 1/3 of 6 mm aluminum sheet


Floor from 7 mm aluminium sheet.


Floor front 2/3 from 7 mm, rear 1/3 from 8 mm aluminum sheet.


Floor front 2/3 from 7 mm, rear 1/3 from 10 mm aluminum sheet.


Floor front 2/3 from 7 mm, rear 1/3 from 10 mm aluminum sheet (including compensating wear plates on the lower straps in the area of ??the 10 mm floor).

- Attention: Competitors products have no compensating wear plates!


floor from 8 mm aluminium sheet


Floor from 10 mm aluminium sheet


Floor in 10 mm aluminium sheet (Including compensating wear plates on the lower straps).

- Attention: Competitors products have no compensating wear plates!


Foldable Lashing eyes recessed in the aluminum floor.

- Attention: aluminum lower flange with 90 ° -Bodenwinkel required (s.Art number BO01110.)
- Distribution: 1. pair approx. 500 mm from end wall; Last pair about 500 mm inside back wall, rest equally divided.


General remarks on wearing floors:


Steel wear floor made of 4 mm QSTE 690,,Sideways about approx. 200 mm raised


Steel wear floor made of 3 mm HB 450 ,Sideways about approx. 200 mm raised


Steel wear base made of 4 mm HB 450,Sideways about approx. 200 mm raised


Aluminum wear-resistant base made of 4 mm aluminum sheet, Laterally raised over bevel


Aluminum wear-resistant base made of 5 mm aluminum sheet, Laterally raised over bevel


Webac electric vibrator (vibrator) mounted on the bottom of the dump .


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT or RIGHT in driving directional.


Dump walls made of aluminum hollow profiles 40/3/2 mm thick with aluminum upper profile profiles projecting inwards.


Alu wear plates 4 mm thick at the Dump rear side walls (approx. 2,500 mm long, front approx. 250 mm and rear approx. 900 mm high) from AlMg 4,5 Mn W28.


Alu wear plates 5 mm thick at the rear side walls (approx. 2,500 mm long, front approx. 250 mm and rear approx. 900 mm high) from AlMg 4,5 Mn W28.


OUTDOOR ALU pendulum tailgate 17 ° diagonally with surrounding rubber seal (without chute).


OUTDOOR ALU pendulum tailgate 5 ° oblique with surrounding rubber seal (without chute).


Aluminum wear plate 4 mm thick at aluminum tailgate at the bottom, transversely over about 300 mm high.


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Edge protection at the top of the tailgate by means of a stainless steel angle riveted between the pendulum bearings 100x100x5 mm.


Automatic 4-hook rear panel locking with return spring and additional Manual spring lock fuse.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.



.Grain slider rear in back wall with hand lever and cover box ..




Without crossbow.


steel ?round tube-cross bow (Ø = ca. 50 mm) TELESKOPIERBAR with tension lock and bearing at top boom.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- ATTENTION: pay attention to the total height !!
- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- Rising ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010.


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- ATTENTION: pay attention to the total height !!
- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- Rising ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-Schlachte (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimensions approx. 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-SR07

Total weight:35.000 kg
Empty weight:ca. 5.984 kg
Bridge size:ca. 7.300 x 2.340 mm
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 5.984 kg
Payload:ca. 29.913 kg
 
Construction:
Bridge size:ca. 7.300 x 2.340 mm
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:approx. 48°
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-07) with standard frame height, wheelbase 4.640 mm, axle spacing 1.310 / 1.310 mm suitable for 2-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device



3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 7,300 / 1,550 mm (with internal tailgate with chute

-Volume then approx. 24 m?


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Internal steel pendulum tailgate (with chute).


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (3-07) HEAVY-DUTY (RETRO) with standard frame height ,wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm suitable for 2-A tractor.

" STABILITY of that time. TECHNOLOGY of Today"


RHKS chassis (3-07) with HHH frame height for ASH loads from approx. 1,260 to 1,350 mm, wheelbase 4,640 mm, center distance 1,310 / 1,310 mm suitable for 2-A-tractor unit equipment.

- The specified saddle height applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We ask and accurate indication of the unloaded and loaded saddle height!


RHKS chassis (3-07) with EXTRA HIGH frame height for ASH debited from about 1360-1420 mm, wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm fits on 2-A-Tractor unit equipment.

- Required for an extremely high-mounted semitrailer coupling or for tractors with a swivel frame design
- The specified saddle height applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the height of the saddle can change and an extra high frame may not be necessary. We ask and accurate indication of the unloaded and loaded saddle height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).


3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).




SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis in FR LINKS.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation.


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- It must Traction button 2 x pressed in quick succession (to tactile switch in the truck / tractor required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)



tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Round Full-LED-3-chamber-rear lights double (1x 5021908 / 1x 5021911) incl.. LED Blinker failure control (5019685), 2 round rear fog-/reversing-lights (5020731) and 2 separate triangle- retro reflectors.


Additional round Full-LED-3-chamber-rear light (5021908) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Self-steering axle (2 SMST.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Mounting on the axle assembly on RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.



Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


- Kippwinkel dann ca. 52°


Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, all steps hard chromium-plated, 4-point bearing.

- Kippwinkel dann ca. 52°


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 7,300 / 1,450 mm (with internal tailgate with chute)


Steel round trough 7.3000 / 1.650 mm (with external tailgate with chute).

-Volume then approx 25,6 m?


Steel round trough 7,600 / 1,450 mm (with internal tailgate without chute)

-volume then approx 23 m?


Steel round trough 7,600 / 1,550 mm (with internal tailgate without chute

-Volume then approx 24,8 m?


Steel round trough 7,600 / 1,650 mm (with internal tailgate without chute

-Volume then approx 26,6 m?


Steel round trough 7,600 / 1,750 mm (with internal tailgate without chute

-Volume then approx 28,3 m?


Steel round trough 7,600 / 1,850 mm (with internal tailgate without chute

-Volume then approx 30,2 m?


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Webac electric vibrator (vibrator) mounted on the bottom of the dump .


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


Ascent ladder divided at the side wall on LEFT in driving directional. Upper half firmly screwed to dump side wall, lower half to hang in.

- Empty bracket for suspension lead over the axle assembly on LEFT in driving directional.


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Hydraulic, internal pendulum bearing steel tailgate (with chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve for the front lifting cylinder.
With pendulum function combined with 2-hook locking

- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7 pin. White (without pushbutton switch installation in truck / tractor) incl. Emergency function via EBS with touch switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function.


Hydraulic, external pendulum bearing steel tailgate (without chute) incl. Electrohydraulic check valves for the controlled closing of the tailgate and an additional shut-off valve on the front lift cylinder.
With pendulum function combined with 2-hook locking.

- possibly with rubber seal (see No. RW11520)
- PIN assignment for tailgate closing: PIN 11 at 15-pin. / PIN 2 (58R) at 7 pin. White (without pushbutton switch installation in truck / tractor) incl. Emergency function via EBS with touch switch on the chassis.
- Power supply for tailgate opening: via EBS with switch on the chassis to deactivate the hydraulic function


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box



Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump..


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow




REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimension approx : 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-SR07 ISO-R

Total weight:35.000 kg
Empty weight:ca. 6.552 kg
Bridge size:ca. 7.300 x 2.340 mm
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 6.552 kg
Payload:ca. 29.877 kg
 
Construction:
Bridge size:ca. 7.300 x 2.340 mm
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:approx. 48°
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-07) with standard frame height, wheelbase 4.640 mm, axle spacing 1.310 / 1.310 mm suitable for 2-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.



Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 7,300 / 1,550 mm (with internal tailgate with chute

-Volume then approx. 24 m?


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet "brushed" (unpainted)


WITHOUT temperature measuring sensors and cabeling for digital measurement technology (there are, however, empty tubes for later installation)


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Internal steel pendulum tailgate (with chute).


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


Paneling of insulation (unpainted).


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


RHKS chassis (3-07) HEAVY-DUTY (RETRO) with standard frame height ,wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm suitable for 2-A tractor.

" STABILITY of that time. TECHNOLOGY of Today"


RHKS chassis (3-07) with HHH frame height for ASH loads from approx. 1,260 to 1,350 mm, wheelbase 4,640 mm, center distance 1,310 / 1,310 mm suitable for 2-A-tractor unit equipment.

- The specified saddle height applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the mounting height can change and a high frame may not be necessary. We ask and accurate indication of the unloaded and loaded saddle height!


RHKS chassis (3-07) with EXTRA HIGH frame height for ASH debited from about 1360-1420 mm, wheelbase 4,640 mm, axle distance 1,310 / 1,310 mm fits on 2-A-Tractor unit equipment.

- Required for an extremely high-mounted semitrailer coupling or for tractors with a swivel frame design
- The specified saddle height applies only to tires 385/65 R 22.5. Depending on the desired axle type and tires, the height of the saddle can change and an extra high frame may not be necessary. We ask and accurate indication of the unloaded and loaded saddle height!


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.


Jost gearbox support winch with T-foot CENTER mounted on the vehicle (only for empty seats).




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).


3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).




SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis in FR LINKS.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation.


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- It must Traction button 2 x pressed in quick succession (to tactile switch in the truck / tractor required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Loadingmanometer (0-10 bar)



tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Round Full-LED-3-chamber-rear lights double (1x 5021908 / 1x 5021911) incl.. LED Blinker failure control (5019685), 2 round rear fog-/reversing-lights (5020731) and 2 separate triangle- retro reflectors.


Additional round Full-LED-3-chamber-rear light (5021908) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Self-steering axle (2 SMST.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Mounting on the axle assembly on RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.



Binotto highpressure front lifting cylinder, approx. 5.885 mm stroke (approx. 78 l oil requirement), operating pressure. 250 bar, biggest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 5.830 mm stroke (approx. 87 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.

- Tilting angle approx. 52 °


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Steel round trough 7,300 / 1,450 mm (with internal tailgate with chute)


Steel round trough 7.3000 / 1.650 mm (with external tailgate with chute).

-Volume then approx 25,6 m?


Steel round trough 7,600 / 1,450 mm (with internal tailgate without chute)

-volume then approx 23 m?


Steel round trough 7,600 / 1,550 mm (with internal tailgate without chute

-Volume then approx 24,8 m?


Steel round trough 7,600 / 1,650 mm (with internal tailgate without chute

-Volume then approx 26,6 m?


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet cladding "bright annealed" KSM70 bright (unpainted).


Stainless steel sheet panel painted in surface paint.


PREPARING for digital measurement technology incl. 4 temperature measuring sensors on the side walls and cabling.


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Floor made of 8 mm HB 450.


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


Trough walls made of 6 mm HB 450.


- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box


Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- Recommended for road milling insert!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump..


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Paneling of the insulation varnished in mounting color.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimension approx : 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-SR08

Total weight:35.000 kg
Empty weight:ca. 6.456 kg
Bridge size:ca. 7.300 x 2.340 mm
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 6.456 kg
Payload:ca. 29.490 kg
 
Construction:
Bridge size:ca. 7.300 x 2.340 mm
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:approx. 48°
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-08) HEAVY-DUTY (RETRO) with height frame wheelbase 5.000 mm, axle spacing 1.310 / 1.310 mm suitable for3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.


Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 8,200 / 1,450 mm (with external tailgate without ladder).

- Hardox? Stahl-Rundmulde
-Volume then approx 25 m?


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


Externally mounted steel pendulum tailgate (without chute).

- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


Removable side protection according to EC directives.


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.




On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).



3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).




SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis in FR LINKS.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation.


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- It must Traction button 2 x pressed in quick succession (to tactile switch in the truck / tractor required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)



tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Round Full-LED-3-chamber-rear lights double (1x 5021908 / 1x 5021911) incl.. LED Blinker failure control (5019685), 2 round rear fog-/reversing-lights (5020731) and 2 separate triangle- retro reflectors.


Additional round Full-LED-3-chamber-rear light (5021908) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Self-steering axle (2 SMST.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)



PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Mounting on the axle assembly on RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.



HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 6,830 mm stroke (approx. 102 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Floor made of 6 mm HB 450.


Webac electric vibrator (vibrator) mounted on the bottom of the dump .


Climbing ladder at front wall inon left in driving directional.


Climbing ladder at front wall in on LEFT in driving directional

- ATTENTION: steps are also on RIGHT in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Ascent ladder divided at the side wall on LEFT in driving directional. Upper half firmly screwed to dump side wall, lower half to hang in.

- Empty bracket for suspension lead over the axle assembly on LEFT in driving directional.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box


Steel cover plate inside grain feeder for protection from coarse bulk materials, can be operated from the outside.



Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Sliding top protection function in combination with hydraulic tailgate:
- Control unit IP67 with remote control
- Automatic plan fall board

- Sliding roof opens partially before hydr. Tailgate opens.
- Power supply via EBS with roll switch betw chassis and dump..


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow




REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimension approx : 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days

RHKS-3-SR08 ISO-R

Total weight:35.000 kg
Empty weight:ca. 7.014 kg
Bridge size:ca. 7.300 x 2.340 mm
Base data:
Total weight:35.000 kg
Front weight/Support load:11.000 kg
Rear weight/Axel load:24.000 kg
Empty weight:ca. 7.014 kg
Payload:ca. 29.454 kg
 
Construction:
Bridge size:ca. 7.300 x 2.340 mm
Board height:
Pendulum head height:
Front wall:
Rear wall:
Locking:
Platform height (unloaded):
Floor thickness:
Hydraulics:
Lifting force:
Lifting cylinder:
Approx. tilt angle:approx. 48°
 
Build:
Top speed:
Spread:
Brakes:
Rims:
Tyres:
Chassis finish:
Build finish:

RHKS chassis (3-08) HEAVY-DUTY (RETRO) with height frame wheelbase 5.000 mm, axle spacing 1.310 / 1.310 mm suitable for3-A-tractor unit equipment


Rigid tipping shaft with 2 lubricable tipping bearings and rubber pads for noise damping.


Saddle plate with exchangeable 2 "kingpin.


Rear underride protection can be folded according to EC directives with TENSIONAL support.


without abatement device


3 x SAF 9 ton axles (ET 120 mm) for 22.5? wheels, Airvent with large Intradisc brakes Ø=430 mm in CD execution (OFFROAD)


double sided axle lift at 1st axle controlled via EBS with integrated traction support (30 %/30 km/h), switchable electrically in the drivers cabin. .

--PIN Assignment: PIN 12 at 15 pol. / PIN 6 (58R) at 7 pol. white (without switch installation in the drivers cabin). -traction support also activatable by pushing brake pedal 3 x.


Brake- / light connections at the front of the chassis frame viewed from left on direction of travel : EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


Brake connection front exchangeable with red and yellow coupling head.


without connection tubes /cables to the truck


EBS Brake installation Knorr incl. RSP ( Roll-Stability-Programm )

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


EBS 2S/2M.


spring wheel lock acting on 2 axles.


CONVENTIONAL air suspension with mechanical Air spring valve, QUICK-RELEASE and manual lift / lower rotary valve with RTR function from 10 km / h (Reset to Ride).


steel air container


lighting installation 24 Volt acc. to EC-guidelines


electrical connection front 15-pol. and 2 x 7-pol..


without coiled connection-cable to truck


LED front and bottom position light (5015486).


1 set LED- side marker lights (5015488).


1 pair LED-rubber bracket-contour lamp rear (5019489/90).


1 pair partial-LED-rear light module "Easy Conn II" (5019493/94) with LED-brake-parking light


1 pair LED-number plate light rear (5019491).


6 pcs. tyres 385/65 R 22,5 TL 160 K brand at the discretion of manufacturer (regional profile). 702,0 kg 3.060,00 €


steel rims 11,75x22,5 10-hole offset 120 mm.


single wheel PVC mudguard.


injection flaps made of REINFORCED RUBBER / TISSUE material with chain and hinge on the rear fenders.


Plastic chock with bracket.



Towing eyelet at the rear of the frame end on left in driving directional


holder for shovel/broom/grate etc. consisting of 2 folding-Holders with 2 lock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connecting hose fixed to the trailer / saddle trailer.


Pressure-connection: screw coupling slack part HDK BG6.


Steel round trough 8,200 / 1,450 mm (with external tailgate without ladder).


Important note on the use of steel troughs made of high-strength steels:
These are not suitable for chemically aggressive media (eg acids, chlorine compounds, sulfur compounds, "substitute fuels", etc.); Such media can lead to stress corrosion cracking in conjunction with the moist depression surface and thus to extreme cracks in the cavity body!


ISOTEXX round cylindrical thermal insulation, approx. 60 mm thick, outer casing covered with high-quality stainless steel sheet.


Stainless steel sheet "brushed" (unpainted)


WITHOUT temperature measuring sensors and cabeling for digital measurement technology (there are, however, empty tubes for later installation)


Floor made of 5 mm HB 450.


Steel front wall 17 ° oblique with stable upper belt and support brackets for front lifting cylinder.


Steel standing column mounted on the chassis with ALU grating, railings and appearance.

- Ascent on LEFT and RIGHT in driving directional.


Trough walls made of 4 mm HB 450


- ATTENTION: 100 mm less overhang of the trough than in the case of chute - can have a negative impact on the final use of the insert !!
- possibly with rubber seal (see No. RW11520)


Simple pendulum bearings on the outside tailgate.


WITHOUT rubber seal.


Automatic 2-hook backplane locking with return spring and additional Manual plug securing.


Hand strap on swing tailgate.


Cross brace "LIGHT" with empty brackets on the upper strap.


PVC-tarp in 900gr/m? panama-qualit with 3 folding tarpaulins.


Reinforced aluminum roll-up profile with crank.


PVC-tarp mounted on the right drivingside


Top lashing with single expander rubber.


Planing lashing laterally as CENTRAL LATCH with ALU-CIRCULAR, which can be rolled onto the side wall, with closure on the front wall.


Rear lashing with 2 V- EXPANDER RUBBERS


tarpaulin color sio-line-nr. _____ (similar to RAL _____) at your discretion


Hanger hook approx. 2,000 mm long.


Chassis and steel tray with 3-layer lacquered incl. Additional zinc dust primer.


chassis 1-colour in standard black-grey.


1 steel rims in silver acc. aluminum-rims unpainted.


Trough 1-color in RAL ______ according to your choice.


Paneling of insulation (unpainted).


warn markings for transversal bows externally at side walls left and right


contour marking strip acc. ECE 104 laterally in white


contour marking strip acc. ECE 104 rear in red


COC-approval document.


REISCH- driving jacket


Removable side protection according to EC directives.


jost gearbox support winches ( module B0101-040304) with T-food


Jost gearbox support winches (module B0101-010304) with S-foot and base plate.


Jost gearbox support winch with T-foot CENTER mounted on the vehicle (only for empty seats).




(100x100x4 mm square tube approx. 200 mm long), WITHOUT laterally insertable molded-tube support feet (for empty stowage), screwed on the saddle support consoles.


On the seat support bracketsscrewed-in pockets (100x100x4mm square-neck approx. 200 mm long), MIT 2 side-insertable, non-height-adjustable tubular support legs (60 kg not included in the vehicle lee weight) (for empty stowage).

- exact specification about the lowest and highest set-up height is absolutely necessary!


3 x SAF-9-to- axles (offset 0 mm) for 22,5"-E- tyres INTRADRUM with drum brake
420 x 180 mm intra CD (OFFROAD).



3 x SAF-9-to- axles (ET 120 mm) for 22,5"-E- tyres, INTRADISC with large INTEGRAL disc brake Ø=430 mm intra CD (OFFROAD).



SAF air bellows Ø = 300 mm



3 x BPW-9-to- axles (offset 0 mm) for 22,5"-E- tyres with drum brake 420 x 180 mm, ECO-Air-COMPACT-HD (OFFROAD).


3 x BPW-9-to- axles (ET 0 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets strengthened axle beam and strengthened single leaf suspensions 70/62 mm (OFFROAD).


3 x BPW-9-to- axles (ET 120 mm) for 22,5"-E- tyres with large disc brake Ø=430 mm as well as SB-cover sheets,ECO-Air-COMPACT-HD (OFFROAD).


BPW air bellows Ø = 300 mm


Hubodometer Axis Cap kilometer counterr MECHANICAL.

- Mounting on 2nd axis in FR LINKS.


Rear axle (9-to) as friction-steered steered tailgate (approx. 12 ° steering angle) including steering damper.
Reversing lock via reversing headlights AND via switch in driver's cab switchable, also via manual shut-off valv.

- ABS then 2S2M + 1SLV.
- PIN assignment: PIN 11 at 15-pol./ PIN 2 (58L) at 7-pol. white (without switch installation in truck / tractor).


without axle lift.


traction help (30 %/30 km/h) at 1. axle (without axle lift) switchable electrically via drivers cab.

- PIN assignment: PIN 12 at 15-pin. / PIN 6 (58R) at 7-pin. White (without touch switch installation in truck / tractor)
- additional. Can be activated via 3 x brake pedal actuation.


Traction with additional GROUND FUNCTION (50% / 20 km / h).

- It must Traction button 2 x pressed in quick succession (to tactile switch in the truck / tractor required).


controlled 2-sided axle lift for 9-to-axis on 2nd axle via EBS and switchable together with the 1st axis.


2-sided-axle lift for 9-to-axles at 3. axle operated via EBS and switchable with 1.
axle.


Brake / light connections at the front of the pedestal of the right in direction of travel: EBS / 7-pol. White / brake red / brake yellow / 7-pol. Black / 15-pol.


DUOMATIK-brake connection front (instead of red /yellow draw gear head).

-Mounting on RIGHT in driving directional.


DUOMATIK- brake connection front in addition to red /yellow draw gear head

-Mounting on RIGHT in driving directional.


EBS-brake system WABCO incl. RSS (Roll-Stability-Support).

- With standard provision of axle load data on EBS modulator to tractors for axle load display in cab (truck / tractor must be prepared / unlocked it).


KNORR-TIM as Trailer-Info-Module (despite conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


WABCO-SMARTBOARD acting as Trailer-Info-Module (despite of conventional air suspension).

- For reading Mileage, EBS diagnostics, axle load / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Additional brake for road finisher.

- PIN-assignment: PIN 10 with 15-pol./ PIN 5 (R) with 7-pol. White (without switch installation in truck / tractor).
- for this purpose, we recommend KNORR-TIM (see item number BR02100) or WABCO-SMARTBOARD (see part no. BR02120) for setting / changing the paver brake pressure!


Brake pad wear display for disc brake acting on 3 axles ABS/EBS warning display
Acting in drivers cab.


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 15 km / h (reset to ride).


ELECTRONIC air suspension WABCO with travel sensor, electr. QUICK-RELEASE AND ELECTRIC. Lifting / lowering control panel with RTR function from 10 km / h (reset to ride).

- SMARTBOARD for reading KM stand, EBS diagnosis, axle loads / bellows pressures; Operation of the axle lift / first aid on the trailer; Adjusting the brake pressure at the final brake, etc.


Automatic air suspension lowering device when tilting, can be deactivated on the chassis.


Aluminium air tank.


Load pressure manometer (0-10 bar) fitted at front left side. (acting on 2. Axle)


Loadingmanometer (0-10 bar)



tyre pressure ?control system acting on 6 wheels (Wabco-IVTM) with display in the truck (if suitable for this purpose) and on Smart-Board (if installed on trailer).


full-LED-rear light-module "Easy Conn II" (5019956/57) incl. LED Blinker failure control (5017624).


Round Hybrid-LED-3-chamber-rear lights double (1x 5021909 / 1x 5021910) incl.2 round rear fog-/reversing-lights (5021907) and 2 separate triangle- retro reflectors.


Additional round Hybrid-LED-3-chamber-rear light (5021909) as spare part.


Separate square LED- reversing lights (5012544) rear.


Separate square LED- reversing lights (5012544) in area of landing gears.


Separate square POWER BEAM-LED- reversing lights (5010316) rear.


Separate square POWER BEAM-LED- reversing lights (5010316) in area of landing gears.


LED warning light yellow "SPEED CAMERA" (5013026) at the rear

- PIN assignment: PIN 14 at 15-pin. / PIN 4 (54) at 7-pin. White)


working flood light mounted rigidly (rotatable- und swiveling) on telescope tube (ca. 750 mm extricable ) exterior at platform-banister with statically fitted power supply.

- Power supply to parking light switched.


acoustical reversing warning signal switched via reverse gear.





spare tire 385/65 R 22,5 TL 160 K.

- Make our choice on STEEL WHEELS !!


steel rim 11,75x22,5 10-hole offset 0 mm.


"Alcoa"-aluminum rims BRUSHED 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with
stainless steel-wheel nut-cap


"Alcoa"- DURA-BRIGHT 11,75x22,5-10L with offset 0 mm, hole-Ø 26 mm with stainless steel-wheel nut-cap.


Alcoa"- aluminum rim BRUSHED 11,75x22,5-10L with offset 120 mm, hole-Ø 26 mm (5-to-carrying capacity) with stainless steel-wheel nut-cap.


"Alcoa"- aluminum rim DURA-BRIGHT 11,75x22,5-10L with offset 120 mm, hole -Ø 26 mm (5-to-carrying capacity) stainless steel-wheel nut-cap.


Continuous flaps on underrun protection pendulously mounted.


"VOGEL"-Progressive-central lubrication system for grease. (without pump)

+ Price per lubrication point (see No. FZ01370)


"VOGEL"-single nipple-lubrication system for grease

+ Price per lubrication point (see No. FZ01370)


"Vogel" lubrication point

The following components are lubricated:
- Drum brakes axles (12 SmSt.)
- Disc brakes axes (0 SmSt.)
- Self-steering axle (2 SMST.)
- Front lifting tipping cylinder bearing at the bottom (2 SmSt.)
- Front lifting tipping cylinder top (2 SmSt.)
- Rear tipping shaft (4 SmSt.)
- 2-hook linkage lock (6 SmSt.)


PVC-tool box approx. 600 x 400 x 500 mm (WxHxD), lockable.

- Mounting on the axle assembly on RIGHT in driving directional.


Water tank made of plastic approx. 30 ltr. Capacity, width 350 mm, length 430 mm including bracket, filler neck and drain cock.

- Installation on the chassis longitudinal beam on LEFT in driving directional.


Towing eyelet at the end of the frame additionally also on left in driving directional


Towing coupling with plug at the rear of the frame end on right in driving directional.


(4 pcs.) Hook on the chassis length brace on left in driving directional as an empty bracket for a towing cable.

- Length of the tow rope, please specify!


Aluminum ladder, approx. 2.400 mm long (8 rungs) with lockable bracket

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


1 piece aluminum-ladder approx. 2.950 mm long (10 rungs) with lockable holder.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.


Aluminum ladder, approx. 3,500 mm long (12 rungs) with clamp-on bracket hooks for mounting on the side of the upper strap, incl. Empty brackets on the chassis.

- Bracket on the chassis longitudinal beam on RIGHT in driving directional.



HYVA high / low pressure front lifting cylinder, approx.6,230 mm stroke (approx. 93 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


HYVA high / low pressure front lifting cylinder, approx. 6,830 mm stroke (approx. 102 l oil requirement), operating pressure 170 up to max. 250 bar, smallest step hard chromium-plated, 4-point bearing.


Hydraulic connection fixed directly on the front lifting cylinder (without connecting hose to the truck unit equipment).


Pressure-connection: screw coupling rigid part HDK BG6.


Pressure-connection: screw coupling rigid part Hyva 1".


Pressure-connection: screw coupling slack part Hyva 1".


Floor made of 4 mm HB 450.

- not suitable for demolition and rock transports!


Climbing ladder at front wall inon left in driving directional.


Lifting ladder at the front of the sliding roof canopy on LEFT of driving directional.


Ascending ladder at the front wall on LEFT in driving directional can be pulled out to the side, lower part can be folded down with holding handle and entry steps in the dump.


Holder for shovel / broom / rake, etc., consisting of notched angled bracket at the top and round-tube handle guide at the bottom of the front wall-outer side.

-Mounting on LEFT and RIGHT in driving directional.


Trough walls from 3.2 mm HB 450th

- not suitable for demolition and rock transports!


Trough walls made of 5 mm HB 450.


DOUBLE JOINT-pendulum bearings on the outside pendulum tailgate.


Interchangeable, reinforced triangular full-rubber cover for outside tailgate.


-Additional securing by means of bolt on the inside tailgate to keep open for cleaning the dump


Additional linkage at the outboard tailgate for use as a pulling device or tailgate holding device for the outboard tailgate.


Locking device (pulling device) for 75/150 mm opening height at the inside tailgate.


Asphalt pusher rear in swing flap with hand lever and cover box


Without crossbow.


Roof-shaped roof rack with approx. 100 mm roof pitch consisting of 2 straight steel round tube crossbars (Ø = approx. 50 mm) TELESCOPICABLE with TENSION CONNECTION (1 x center and 1 x shortly before the swing tailgate), as well as a right- = Approx. 50 mm), which is provided on the underside with a 50 mm spacer at the front, at the crossbars and at the rear.


Without rolling tarpaulin.


Longer tarpaulin overhang.


tarpaulin tie down lateral with hand lever-tension ratchet, tension belts a. spacers.


tension belts in silver, black, white, yellow, red, orange, or blue (please choose)


Protective tarpaulin on tailgate in high-quality 1,400 gr / m?-quality with ked rails and belt fastening (tarpaulin color black).

- Recommended for road milling insert!


Cramaro convertible top convertible type C with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, linkage folding hinges, automatic tailgate, windproof hook system with continuous Z-profile rail, front wall protection roof, electric drive With radio remote control.
WITHOUT connecting line to truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Cramaro sliding top.


Cramaro PVC tarpaulins in ADR flame retardant.

- ATTENTION: restricted color chart selection - possible colors: PFC1003, PFC3002, PFC5002, PFC6001, PFC 6026, PFC7038, PFC9010


Cramaro PVC tarpaulins based on POLYURETHANE up to 180 ° C temperature-resistant.
Black.


Plan color according to Cramaro color chart Cramaro -_____ (similar to RAL _____) according to your choice.


Marcolin sliding hood model Eletta with 650 gr / m? PVC tarpaulin, bow height approx. 300 mm with 100 mm lateral overhang, automatic tailgate, end wall protective roof, electric drive with radio remote control.
WITHOUT connecting line to the truck / tractor and without truck / tractor installation.

- Possible access / entry aids:
- on the front wall, Foldable folding ladder (see No. ST10900)
- Aluminum conductor 3,500 mm with hooks (see item number FZ02360)
- split ascent ladder on the left side (see number SW19100) - not possible with ISOTEXX!
- ascent ladder to the sunroof protection canopy on the left (without access possibility) (see part no. ST10850)
- additional truck / tractor cable installation kit recommended (see code SV04120)
- additionally gallows on the tilting cylinder for hydr.-tubing (s.Art-Nr. AZ10500) urgently recommended.


Manual drive with hand crank at Marcolin sliding top.


Marcolin PVC tarpaulins in ADR flame retardant


Marcolin tarpaulin on SILIKON-basis up to 130 ° C temperature-resistant.Trapaulin color Black


Marcolin color chart Marcolin -_____ (similar to RAL _____) according to your choice.


Electric connection for sliding hood with NATO socket (WITHOUT connecting cable and WITHOUT truck / tractor installation).


Cable installation kit for trucks / tractors incl. Connection cable for power supply trailers / trailer trolley (WITHOUT installation in truck /tractors ).


Boom mounted on tilting cylinder to hang up the hydraulic connecting hose to the tractor.


chassis 1-colour in RAL _____ at your discretion.


axle hub in RAL ______ at buyers option.


Dump 1-colored in 2-layer METALLIC color according to your choice.


Side wall upper belt on both sides different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt and hollow rear frame different colors in RAL ______.


Side wall upper belt on both sides, end wall upper belt, rear frame of rear body and tailgate mount different color in RAL ______.


Paneling of the insulation varnished in mounting color.


Dump with additional clear coat.


Full marking plate (? 197 x 1132 mm) ECE 70.


A-board foldable


Warning sticker "Construction vehicle" red / white / red framed, approx. 650 x 200 mm.

- Mounting bottom center on the chassis rear.


Warning sticker "Attention construction vehicle" red / white / red framed, approx. 1.400 x 200 mm.

- Mounting the top center on the tailgate.



contour marking strip acc. to ECE 104 lateral in yellow


contour marking ?strip acc. to ECE 104 rear in yellow



REISCH-advertising label with large REISCH-Logoar left and right hand side at the side wall in rear area

Dimension approx : 3.000 mm x 730 mm


Customers-markings acc. to delivered pattern


TÜV-/DEKRA-inspections acc. ? 21 incl. german certificate for obtaining an operating permit


export license (customs plate) for trailers/semitrailers incl. insurance for the period of 9 days